This is default featured slide 1 title
This is default featured slide 2 title
This is default featured slide 3 title
This is default featured slide 4 title
This is default featured slide 5 title
 

Category Archives: Home Improvement

Caring Leather Bed Frames

It is regularly a test when guidelines that accompany furniture are not as circumstance particular and educational as proprietors might want them to be. Keep in mind that upkeep for calfskin bed outlines contrast from looking after a wooden bed outline and additionally exemplary beds. This guide serves to help proprietors in administering to any sort of genuine cowhide furniture may it be a bed outline or a couch set.

Before beginning the cleaning procedure, ensure you comprehend what sort of cowhide furniture you have. This can more often than not be found in the labels that accompany your new furniture or in the guideline manual. There are numerous sorts of cowhide utilized for furniture and not all are the same. To ensure you know precisely what sort of cowhide you have, it is best to do the hunt online as there is a procedure to test the calfskin to decide the its sort.

Leather is very delicate material and extremely sensitive to heat. Make sure you place furniture away from fireplaces and direct sunlight. Neglecting to do so can dry and crack the surface of the leather. When you notice an area that is getting too dry than it normally would be, use petroleum jelly to cover the area and just wipe off the excess amount.

To clean your leather furniture use soap that is not too harsh and has a moisturizing element in them. Use a soft cloth with soap to wipe the surface to remove dirt. Do not put too much soap and do not rinse it with water. Leather absorbs water so it is important not to use water. Just wipe the soap off with a dry cloth and polish it after.

Always use a leather conditioner to maintain the glamour of your furniture. Good leather conditioners can be bought anywhere but make sure that you read what you are buying before purchasing them. For the best results use a leather conditioner that has been tried and tested. Rub the conditioner around and leave it in for some time so the leather can absorb it then buff after with a dry soft cloth.

Avoid spilling liquid on your furniture because leather may absorb it. A quick fix for liquid spills on leather furniture is to use a clean cloth to dab the wet area while being careful not to spread the liquid outwards. Dab inwards starting from the sides and keep dabbing until it is dry. Allow it to air dry.

Now butter, grease or oil stains are not to be panicked about. Just wipe it off with a dry cloth until everything is removed and leave it that way for a few days. In most cases, this will not be visible anymore by this time but if the stain is still obvious, use leather furniture cleaner to repair the area.

Ink stains can be removed by a simple piece of cotton or cotton bud that is soaked in alcohol or vinegar. Rub it over the stained area and that should remove the ink stains. However, if the stain would not come off, use an acetone-free nail polish remover to do the trick. Once done, use a hair dryer on low setting to dry the area.

Printed paraphernalia if left on your furniture can leave print marks. To remove this, use a can of aerosol hair spray on the affected area, spraying ever so slightly then wipe it off with soft cloth immediately.

A few reminders to ensuring you can avoid damaging your furniture are a few basic things that every individual already knows. Use your furniture appropriately. Do not sit on the foot end as it is not intended for this purpose and sitting on it can distort the shape of your furniture. Also, if you are a smoker, it is best to avoid leather furniture as cigarette burns on leather cannot be repaired.

Furniture of any kind such as a wooden bed frame, leather bed frames or classic beds are only a worthy investment if it can last. Buying new furniture due to neglect of the current set is a waste of money. So before purchasing any kind of furniture it is best to be aware on how it is maintained so you know if you can commit to caring for it. Furniture always needs love and care every so often and it is up to you to keep its beauty and durability as good as new.

Guide to Hanging Wall Frames

One of the most ideal approaches to beautify the dividers of your home or office space is by hanging divider outlines, which arrive in an assortment of sizes, shapes and materials. A prominent casing size most generally utilized for a representation is a 16×20 picture outline and the 24×36 picture casing is an awesome size for encircling a canvas. The different materials from which casings are made incorporate wood, metal, and plastic. Picking an edge that best complements the photo or fine art you need to show is constantly imperative, pretty much as ensuring the edge is accurately held tight the divider. A disgracefully hung divider edge can be unattractive and ruin the entire thought of improving the rooms style. By picking the proper style and size of casing you can upgrade the general atmosphere of your home basically.

At the point when hanging divider outlines on drywall it is best to utilize a stud discoverer with the goal that you can hang the casing securely and safely to the divider by pounding a completing nail at a 45 degree edge into a wood stud. Whether you are hanging a 8×10 or a 24×36 picture outline, utilizing a stud is constantly valuable, however by all account not the only technique utilized for hanging divider outlines. In the event that the studs are not in the zone where you might want to hang the casing then you ought to utilize a photo snare that backings the correct weight of your casing. There are a wide range of sorts of picture holders accessible and most function admirably for pretty much any size of edge from the exceptionally littlest to the biggest. For the bigger and heavier edges a decent snare to utilize is unified with three nails which can bolster things weighing from 50 to 100 pounds.

Another method for hanging wall frames is to use screws. Screws are not usually used on regular sheet rocked walls because picture hangers designed for drywall make smaller holes in the sheet rock and offer a more securely hung frame. Screws are usually used on walls made of concrete, stone or brick because these type of walls need the extra support and strength of the screws. With the help of a drill and mason drill bit, drill a hole into your wall and insert the screw. You may also want to consider using a screw anchor which will secure the screw tightly into the wall so that you can hang large and heavy hanging wall frames safely.

You can also use adhesives for hanging wall frames. They are simple and fast and do not require any holes to be made. Different types of adhesives are available in the market today. You can speak to the salesperson and he will show you the different varieties available. The greatest advantage of using adhesives is that there is no need to drill holes on your wall unlike other methods. You can simply choose the area and stick them wherever you want to hang your picture. However, you cannot hang heavy pictures using adhesives. Adhesives are typically used for hanging small frames such as a 5×7 frame. Some kinds of adhesives will hold wall frames up to 5 lbs.

In summary, when choosing the correct method for hanging wall frames there are several things to consider, such as the size and weight of your frame, the location on the wall, as well as the type of wall the frame will be hanging from. So, choose one of the above mentioned methods to hang your favorite pictures or paintings when decorating you home or office space. For a decorator designed look, select wall frames which exemplify styles, colors and materials that complement other items in your home/office decor.

Adding Unique Lamps

One of a kind lights can include extra lighting, character, and style to a room’s stylistic layout and additionally upgrade the magnificence of a home. Lights are offered in a wide determination of one of a kind styles, structures, shapes, and sizes that supplement an assortment of stylistic theme styles and topics. On the off chance that you might want to flavor up a room’s stylistic layout without spending a lot of cash, you might need to consider adding interesting lights to your stylistic layout space. You can discover a wide range of abnormal styles that can add definition and style to a room, and won’t vacant your wallet all the while. By picking a light as an enriching accent, you won’t just add useful mind-set lighting to your room, yet will likewise include character and appeal in the meantime.

An option you may want to consider when looking for unique lamps to add to your home decor are lamps with an unusual base or lamp shade that complement your home decor style. This is a great option for a room with an overall themed decor that you would like to perk up or add dimension to. For example, if you have a room with a beach feel or theme, you might want to add a light fixture or lamp that has more of a nautical look to it. You could choose a table lamp featuring a ship’s wheel, an over sized piece of coral, or even a giant seashell as the base. Any one of these base styles ties in perfectly to a beach themed room and will also give you the extra lighting you may need. Today, there are all sorts of unique lamps to choose from that complement a multitude of decor styles that can be found at great prices.

Although there are numerous styles and designs to choose from, finding unique lamps that suit your personal style or needs is not always an easy task. If you find yourself in this situation there is another option you may want to consider. You can easily make your own lamp using a lamp kit purchased at a hardware or an arts and crafts store. A home decor accessory that complements your decor theme, such as a figurine or vase, can be used as the base of the lamp. You can then purchase a lamp shade in the color of your choice and embellish it with accents and trim if desired, making a one of a kind lamp and shade sure to empress all.

A detailed or colorful lamp shade is a great opportunity to show off a little of your personality and style. Although you may want the shade to allow the right amount of light into the room, there is nothing that says you have to stick with a basic white or off-white toned lamp shade. You may want to go with something totally different to bring a little interest or color into your home decor. Whether you choose a shade with a pattern, a vibrant color, or decorative accents such as fancy braids and beaded trims dangling form the bottom of the shade, it is all about adding a little bit of uniqueness to your space.

Shabby Chic Home Decor

shabby-chic-home-decorThe Shabby Chic stylistic layout style promoted by Rachel Ashwell and Arhaus try to have a rich vintage look. Hues common are white, pastel and ecru. Textures are liberally trimmed giving a delicate and profound feeling.

Shabby Chic furniture is given a troubled look by being secured in sanded drain paint. The entire stylistic layout style has a captivating bug showcase look. Once painted, taking a bit of sand paper and going daintily over various regions of the piece will give the piece the troubled look. Just you will know whether it was new or vintage.

Pink peonies collaboration

Items in this range have soft pink fabric covers and include beddings, bed skirts, settee upholstery, and pillows. Styles in this range are charlotte, petticoat, tufted and Lilliput. Any couch or chair can become Shabby Chic by using a shabby chic fabric cover and pillows.

Rugs

The Shabby Chic rugs are in sheepskin and vintage designs. The sheepskin rug is made from natural sheepskin and is milk white. The vintage rugs are in soft pinks and browns on white backgrounds depicting natural plant art.

Accents

These are different accessories that show spontaneity in art and craft. Items in this collection include poufs, metal trays, globes, matchboxes and vases. Colors are more divergent with indigo, poufs, blue vases and brown wood decorations.

Mirrors

An opulent decor style is bound to have mirrors in various designs. The Shabby Chic mirrors styles are long, liberty, renaissance, estate and grand. Frame colors come in silver and tan colors.

Pillows

The Shabby Chic pillow designs are damask, Bella, lace and Venetian. The emphasis is on a deep fluffy look with covers being dominantly pastel and ecra in color.

Window covering

Curtains are for privacy as well as decorative functions. The range of curtains come in petticoat white, silk dupioni, embroidered voile and cottage linen styles. The colors are white and pink.

Throws

The throws have a hand knit look and go very well with soft pink and white couch and settee covers.

Art

No decor style is complete without art. The works of art in the collection are by Jorunn mulen. The pencil and charcoal etched drawings are done on soft pink and pastel colors to stay with the theme.

Furniture

Shabby Chic has furniture items for dining, living and bedrooms. The Shabby Chic furniture is covered in white, pink and pastel colors. Dining sets, settees and reading bureaus are also in the furniture collection. This is where the distressed look comes into play and really creates the Shabby Chic decor.

The shabby chic decor style also includes lighting, bath and gift items. Baby items are also available in this refreshingly feminine collection. The shabby chic collection is able to give a complete look for the whole house with tasteful items for everyday use. From candle holders to wall hangings, each item brings its own special something to the room.

Caring Decor Furniture

Nothing says shabby in regards to a home like messy and exhausted furniture. Numerous individuals will purchase great furniture yet let it rundown by sheer carelessness or absence of expertise on nurturing it. In different cases the furniture might be exhausted by the substantial and damaging use. On the off chance that the furniture was of low quality it separates rapidly.

Stylistic layout furniture particularly that secured in upholstery can get messy very quick if not tended to well or presented to tidy and mud. Couches, beds, and other furniture secured upholstery are likewise helpless to blur with time if left in unforgiving daylight.

Shabby chic furniture shop have a few tips to share on the most proficient method to administer to their troubled stylistic layout furniture.

Cleaning

Upholstery should be vacuumed at least once weekly and the loose covers laundered weekly too. If you have loose cushions, place the cushion in a large plastic bag, close the bag tightly around the vacuum hose with the hose pressing on the cushion and turn on the vacuum. The cushion will shrink down sucking all the dust particles out of the cushion. Once you turn off the vacuum, the cushion will go right back into shape. Dirt that has fallen in hard to reach places like crevices under cushions should also be cleared with a narrow object. Rough objects can wear on the fabric if not removed.

Protecting fabric

Spills and stains can be avoided by using spray fabric protectors. These can be applied when the upholstery is being installed. You can also buy commercial products. The commercial products work pretty good and is best to have protectant applied prior to use. Either type is better than nothing at all.

Caring for cushions

Cautions that remain at one point for long tend to sink as they get sat on day after day. It is important to flip them and rotate them to another spot.

Rearrange furniture

To avoid one item being used too frequently and wearing out faster than the rest of the furniture, rearrange the furniture at least once in six months.

Rest covers

Headrests, chair backs and armrests wear out faster than the rest of the parts. They also get dirty faster as they come into contact with bare skin and hair. One can get a cover for the rest in the same color. These covers are barely noticeable but very effective in protecting the upholstery fabric.

Washable slip covers are very good to use in warm weather as they can be easily washed while they effectively protect the furniture against stains and spills.

Caring for bare wood

For bare parts of furniture, a damp cloth should be used to wipe off dust and any other stains. Dusting frequently is advised to prevent the dust from caking into a hard coat that is harder to get off.

You can choose to renew the shine on bare wood by using polish or wax. Applying polish is easier but polish can cake up if applied too many times. Wax can be washed off with oil soap and a new coat applied.

When the upholstery gets too old you can always head back to Shabby chic furniture shop for new distressed home decor.

Home Improvements Popular Trends

Home redesigning is done either due to individual intrigued or as a result of prevalent patterns. There are advantages and disadvantages for doing both that we will concentrate on. At the point when mortgage holders rebuild in view of patterns that are prevalent in the home change industry it might enhance the odds the property holder has at recovering the cost that was put into the redesign. The concentrate today will be on prominent lodging patterns and how to function to your greatest advantage and recover the cash you put in.

Front Entry Home Improvements : The expansion of another passage entryway alongside a few upgrades in paint, new carpets and a touch of crisp greenery can truly help the appeal of your home and the general bid of the home’s outside.

Home passage redesigns can cost a normal of five hundred to a thousand dollars. Another front section entryway can cost around six hundred and a quarter century with paint and carpets running another fifty dollars. Section finishing makes up whatever is left of this upgrade making one hell of an arrival on your venture when the time comes to offer.

Bathroom Renovation and Remodeling: Although a bathroom renovation may require more time and money than other home improvement projects it is will also draw in the most attention from buyers. Bathroom remodeling is also known as one of the best return on investments within the home improvement industry.

If you aren’t looking to do a complete overhaul on a bathroom which can cost upwards of twenty five thousand dollars consider simple updates that easily recoup their value. Replace sinks, cabinets and countertops along with fixtures to create an update remodel. Consider a fresh coat of paint and some updated linens for a complete bathroom makeover.

Garage Replacement Door and Remodel: This is a renovation that is not often considered when homeowners think about upgrading the exterior of their homes. Replacing a garage door and updating the space adds to the total value of your home. At resale you are apt to collect at least eighty seven percent of what you put into out of a garage renovation. A new garage door can turn an old outdated exterior into a modern marvel.

Don’t just repaint the garage door replace it. A garage door replacement ranges from around seven to eight hundred dollars all which is usually recouped within the sale of the home.

Purchasing Pool Safety Fencing

Summer is upon us and with that comes the season numerous youngsters and guardians alike sit tight all winter for, swimming pool season! The time when the sun is sparkling, children are outside far from innovation and full scale unwinding happens. With every one of the advantages pool proprietorship brings it is anything but difficult to disregard the risks that join owning a pool. It is essential that property holders set aside opportunity to address security concerns while the pool is being introduced and keep up on keep up the wellbeing of the pool and its surroundings all through the season.

One vital security include that is an absolute necessity amid the establishment of your new pool is a border fence. Fencing is an element that ensures both property holders and pool clients. Having a hindrance between the pool and whatever remains of the lawn permits youngsters and pets to unreservedly utilize the space without being in threat of getting to the pool when not under direct grown-up supervision. Selecting the perfect fencing for a patio pool is a choice that ought not be messed with. The following are components to consider when investigating fencing for your pool’s border.

Considerations to Make When Purchasing Pool Fencing

1) What material will you choose for your pool fence?

The fencing that you choose for the perimeter of your pool should be strong, durable and easy to maintain. One of the most popular materials to use when it comes to pool fencing is aluminum. Aluminum pool fencing is aesthetically pleasing while being durable, easy to maintain and a great protector against inquisitive kids and pets looking to gain access to the pool water.

Whatever material homeowners choose for their pool fencing the most important thing is that they don’t settle or compromise quality over cost or any other variable. Quality fencing is of most importance to ensure the safety of children and pets.

2) Should you choose fencing that is removable or one that is permanent?

For most homeowners this is an easy to answer question; the pool is permanent so the fencing should be permanent as well. This is however not always the case. Some in-ground pools are built in a small space. If this is the case it may be that the fencing need to be removable to allow for more space around the area of the pool. For most homeowners with pools a permanent aluminum pool fence is ideal.

Our next installment on pool fencing considerations we will look into the cost, design, color and installation.

Painting Interior Walls Tips

The dividers of your house are brilliant white, correct? Then again some unattractive shading that needs a change? Furthermore, rather than considering them to be the ideal clear canvases to make an artful culmination, you consider them to be an arduous task you should handle keeping in mind the end goal to enhance the look of your stylistic layout. Like whatever is left of us you presumably do everything to liven up your home-hang pictures, toss down a floor covering or two; everything aside from going up against what you accept will be the terrible errand of painting.

This is justifiable. Since there is so much clashing data out there about painting you likely don’t recognize what to listen to. Well fuss no more. You have halted on the right page. Here you will get a portion of the best tips that will make painting your inside dividers as easy as could reasonably be expected.

The supplies you’ll need to adequately paint your walls are as follows:

Disposable rubber gloves
3-inch flat brush
Small angled brush to paint the trim and/or corners
Newspapers, plastic or a canvas drop cloth to protect floors from paint spills and splatter
The blue painter’s tape that won’t take paint off with it when you remove it
Spackle (to fill in holes and imperfections on the wall)
Putty knife
Sandpaper (to sand down the spackle to a smooth, “paintable” surface)
Turpentine (for oil-based paint)
Pail to wash out your brushes
Cleaning rags
Paint Roller with extension rod to reach tall walls and ceilings
Paint tray
Primer

Pick Your Paint

In order to pick your paint you must first figure out how much of the stuff you are going to need. To do this, measure the square footage of the walls you plan to paint. Paint cans are labeled with the amount of square footage they contain in their cans, so bring along the measurements to the paint store and match them up with each other.

Okay, so you know how much paint you need; now, what type of paint do you need to buy?

There are essentially two types of paint you should choose from: Latex-based paint and Oil-based paint. The easiest to work with is latex-based (acrylic) paint. It can go on walls, floors, and wood and metal surfaces. It is also the easiest to clean up; when you need to clean out your paintbrushes or if some latex paint gets on your skin, a little bit of soap and water will do the trick.

On the other hand, oil-based paint (alkyd-based) is harder to clean up and needs a solvent-like turpentine in order to wash out your paintbrushes and clean the paint off your skin. A plus is that oil-based paint is stain-resistant and adheres to walls and ceilings very nicely. This makes oil-based paint a really good choice to use in your bathrooms and kitchens.

Find A Finish

Now that you’ve picked your paint, you need to decide on a paint finish. Paints and finishes match up in color, so whichever paint color you select get the finish color that matches it.

The types of finishes:

~ Flat finish: This finish is the most commonly used. It is good for large surfaces, and will not reflect light. It is recommend to be used on ceilings, and in bedrooms, living rooms and dining rooms. Not kitchens and baths.
~ Gloss finish: This finish will always reflect light, especially on walls and ceilings and is often used in small quantities (such as on trim).
~  Satin or eggshell finish: This finish is terrific for brightening up hallways, common areas, and children’s bedrooms and playrooms. It can be used anywhere that a slight sheen is wanted.
~ Semi-gloss finish: This finish is easy to clean, which means it is great to use in high-traffic areas such as in kitchens, bathrooms, on doors, etc.

Choose The Color

Never an easy choice to make. Most of us choose a paint color based on a mood or to mimic a photograph we’ve seen in the glossy pages of a magazine. So let’s begin with the basics:

White. If you choose white, you aren’t limited to a boring palate. You can still work within its various color shades. Off-whites, cr�mes and beiges will bring the same bigger feel to your room that a bright white will, and no matter what shade of white, it still the best bet as the background color to your dynamic decor.

Red. If you’d like something more bold and vibrant in your room color, red is a pretty good choice. Maybe not for an entire room, but putting a nice deep red color on an accent wall will give your room dramatic pause. If you aren’t for drama in your room, skip the red.

Blue. You think blue and you think serenity. Blue is a good harmonic choice for almost any room, especially bathrooms. In your bedroom, it offers the feeling of peace and softness. Too much blue can make your room feel cold.

Black. You likely never even considered this paint color, right? Images of a rebellious teen dressed in full black regalia, donning the latest in goth makeup and listening to heavy metal probably come to mind when you think of a black paint on a wall. Although most people will tell you to never paint your walls black, in moderation black could actually be pretty darn cool. You can use black paint on a wall behind your bed as a replacement for a gaudy headboard and take a minimalist approach to your room.

However, I’d say never paint an entire wall black unless you’ve got something strong in contrast to place against it or hang on it. A white and black combination on a wall does wonders, especially if you are going for a dramatic effect. Tip: work in warm colors too (explained below) with accent pillows, curtains, and furniture to take the edge off this very “in your face” paint color.
Other common paint colors include yellow, orange, green and violet. But to sum it all up, the basic tenets of choosing your paint color are as follows: The deep “warm” colors such as reds, oranges, and yellows will produce a cozy room feeling. The light shades, which are your “cool” colors such as green, blue, and violet, will make a room feel more open. White will also give off this feeling.

Select A Shade

There’s nothing worse than selecting a shade of paint that looks great under fluorescent lamps in a home improvement store only to find out later that you’ve brought an entirely different shade home with you. That’s why the best way to select a paint shade is to look at how the color shows under different lighting sources: natural and synthetic. Your synthetic light is whatever bulb wattage you use in your lighting fixtures.

You can avoid making costly mistakes with selecting a paint shade by getting samples of the paints you want, and then using them to paint large sheets of white poster board. You will use these painted poster boards as large, “real world” samples that you can prop up against the walls you plan on painting.

Make sure you critique these poster boards samples throughout the day in order to see how the color shade will look in different light. The poster samples will also give you a sense of how your room will look when it is painted a particular shade and filled with furniture. A word to the wise: deeper paint colors distort more with lighting changes than pastel ones.

Choose Your Paintbrushes and Paint Rollers

This is actually not a hard choice to make. You’ll need both a paint roller and a paintbrush. The paint roller will make paint go faster and puts paint on the wall easier. Of course a roller cannot reach into corners and adequately paint trim and unusual surfaces, so this is where your paintbrush will come in handy. Paintbrushes are good for touch up jobs too.

Avoid using natural-bristle paintbrushes if you’re using latex-based paint. Natural bristles become limp when they absorb water. Instead, use synthetic bristles and rollers for the job. For example, nylon (good for rollers) is abrasion-resistant, and polyester brushes retain their stiffness in water and will maintain their shape. Natural-bristles paintbrushes are best to apply oil-based paint. And use a lamb’s wool roller.

A 3-inch or 4-inch straight-edged brush will handle the general surfaces of your painting project. A 2-inch brush is good to cut-in corners. And an angled sash brush, 1″ to 2 1/2″ wide, is a good choice for painting trim, around window frames and moldings.

To achieve the best-looking paint job you can, you need to use quality brushes. A quality brush has a wooden handle with long, tapered bristles (bristles that are a bit longer in the center than at the edges) that are attached to the handle with epoxy cement instead of glue. The bristles should also have flagged, or split, ends, which is ideal for holding paint and spreading paint equally, smoothly, and with fewer brush marks left on the surface you are trying to paint.

Comfort

Never purchase a paintbrush without first testing it out. Take the paintbrush into your hands and mimic painting a wall. Does the paintbrush feel comfortable in your hand and not awkward or heavy? Remember that you will have to paint your wall with this brush-so make sure the paintbrush is springy, too.

Pile Depth

Rollers come in different pile depths. The pile depth refers to the thickness of the cover’s fiber nap on a roller. It is essential to choose the right pile depth for the surface you plan to paint. In general, a roller with a smoother pile should be used on smoother surfaces, and the rougher piles used on rougher surfaces (to better reach those hard-to-reach areas).

Here’s a breakdown of what pile depth you should use on what surface:

For metal doors and plaster-Very Smooth pile depth
For drywall-Smooth or Semi-Smooth pile depth
For rough wood and acoustic tile-Semi-Rugged pile depth
For textured ceilings and stucco finishes-Rugged pile depth
For concrete block, brick and fences-Very Rugged pile depth

The Prep Work (Getting The Room Ready For Painting)

1. First, clear all the furniture from the room, as much as possible. The furniture that can’t be removed should be positioned in the center of the room and covered with a plastic or canvas tarp. Make sure that the furniture is completely covered, even the legs.

2. Next, cover the floor with drop cloths, tarps and/or newspapers.

3. Now, remove all pictures, artwork and mirrors from the walls.

4. If you painting the ceiling, take down light fixtures

5. Remove all outlet and light switch covers.

When working with previously painted surfaces:

1. Use a mild grease-cutting cleanser to wash down your walls. It is important to remove any dirt, grease and stains so that the paint can adhere to your walls properly.
2. Rinse the wall very well.
3. Remove loose paint with sandpaper.
4. Spackle holes by spreading a thin layer into each with a putty knife. Leave to dry (at least a few hours) then sand gently.
5. Run sandpaper over glossy or nonporous surfaces to help the paint stick better to the wall. Wipe or vacuum away any dust.
6. Apply primer. Primers allow the paint to grip to the wall better and longer. This means your primer will seal the wall and produce a nonporous surface for the topcoat to stick to. Remember to tint the primer to your chosen color by adding a small amount of the paint color to the primer.

Step-by-Step Instructions to Painting Your Walls

Step 1: If you are painting your ceilings as well as your walls, paint the ceiling first. Allow them to dry for at least 24 hours. If you are only painting the walls, go to Step 2.

Step 2: Using your painter’s tape, cover the edge of the ceiling to prevent splattering and protect the trim.

Step 3: Now cover the baseboards and whatever trim not being painted with tape.

Step 4: Paint a 2-inch strip with a small brush along the top of the wall–where the wall and ceiling join.

Step 5: Immediately paint over the cut-in with your roller to keep the paint from drying and leaving a line on the wall.

Step 6: Apply paint to the wall in square-sized sections. With an up and down and across motion, apply a generous coat of paint to the wall. This style will prevent lines when the paint dries.

Step 7: Once the first coat has dried apply another coat.

Repeat the above steps for all walls that need to be painted.

Should You Use The Spray Technique to Paint Your Interior Walls?

The plus side of spray-painting your walls is it’s the least costly painting method of the three methods-brush, roller and spray. It is also the fastest way to apply paint to your walls, and you can cover a large area in a small amount of time, especially if the surface to be painted is more irregular than not.

You can buy an airless spray rig (a pumping unit, hose and a gun). An airless spray rig forces paint through a very small tip, which breaks up the paint into different size spray pattern fans. The benefit of airless spraying is there is little chance of over spray because air isn’t forcing the paint out, which means the room doesn’t become overrun with paint mist.

In general, unless you are a professional painter the spray method is better suited for exterior painting. The spray painting technique must be executed very carefully. However, if you think you can handle the job and choose to take the interior spraying challenge on, you must make sure that you cover your windows, doors and flooring, you have plenty of ventilation, and you wear long sleeves, goggles and a mask before you start painting.

Tips: Paint a small test spot on your wall or surface before taking on the entire wall. Give yourself time to become comfortable with your rig. Point the spray gun directly at the wall. Move the gun in an up and down motion, always moving the painting gun parallel to the surface being painted. If paint begins to run you may be holding the gun too close to surface or wall. Keep a consistent spraying technique to give your wall the best painting job you can.

Replace a Bathroom Vanity

The time has come to makeover a room, and you’ve chosen to turn your considerations to the bathroom. Dreams of a customary withdraw, a nation safe house, or a wonderfully smooth and current washroom have started your renovating fires. In any case, you can’t go anyplace with that old lavatory vanity in the way. So get energized and prepared to go up against a one-day venture of introducing another bathroom vanity. It’s the initial step to making the washroom you had always wanted.

What You’ll Need

Materials

New Bathroom vanity
3″ wood screws
Latex caulk
Pail/Bucket
Quarter round moulding
Washers
Wooden shims

Tools

Adjustable wrench
Caulk gun
Chisel
Combination square
Electric Drill/driver
Gloves
Goggles
Hammer
Hole Saw or Jigsaw
Level
Pencil
Stud Finder
Tape measure
Utility knife

Getting Started

Do you know you can install a new bathroom vanity in a matter of hours? You won’t have to commit an entire weekend to the bathroom vanity installation project unless you want to. That’s the good news. The bad news is installing a new bathroom vanity isn’t easy.

This project isn’t rocket science, of course, but you will need to do some good measuring of the space before purchasing the new vanity to ensure a proper fit. Also, it will take having a bit of muscle to remove the old vanity from the space. And you will need to prepare the space. For example, it is imperative that you check out the installation space for damage and/or problems, and then fix problems before installing your new bathroom vanity.

Removing the Old Vanity

Removing the old vanity sometimes introduces you to a whole host of problems. Common problems include water damage. Your floors can become water damaged from everyday usage. If you discover that this is the case, simply interchange any moldy sections of the floor with plywood.

Also, the drywall may have some water damage. Seeing as drywall is incredibly porous, it will be very difficult to get the drywall to dry out entirely. This means you will need to replace any damaged areas of the drywall if there is any indication that moisture exists. And a good way to help prevent moisture and/or water damage in the future is to install the drywall a few inches above the floor. You can place base moulding over the space that is left between the bottom of the drywall and the floor.

Use a level to make sure the floor’s surface is level in both directions. An uneven floor can be corrected easily with the use of wooden shims or a plywood base. Wooden shims can be placed under the vanity during installation, or you can nail a plywood base to the floor and level it off with shims.

Turn off the Water

Any job involving plumbing requires you to turn off the water supply before beginning the installation project. You can turn off the water supply right below the sink of your old vanity and by twisting off the two valves that are located inside. Or, you can shut off the water supply for the entire house if you need to.

Moving on…

Using an adjustable wrench, loosen the nuts from around the hot and cold supply tubes connected to the shutoff valves. Take your pail and place it directly under the drain to catch any excess water as you undo the slip nut from around the drainpipe. Then undo the nut from around the drain arm that is connected to the wall. Now, take your utility knife and cut away the caulk seal between the sink and the countertop and take out the sink.

If you plan to reuse the sink, turn the sink over and gently lay it down onto an old towel. Carefully cut away any caulk that remains. Clean off the sink well. If you intend on using the sink and the countertop again, however, don’t remove the sink from the countertop. Simply leave the sink inside the countertop and disconnect the entire countertop unit from the vanity base by taking out the screws located on the underside of the countertop.

Taking Measurements

You will need to get good measurements to begin with to avoid making costly mistakes. First, measure the vanity height and width. Do this by measuring the height of the vanity up from the floor in three different places. Using a pencil (or a marker for tile), mark on the wall the height of the vanity from the floor straight up. Make sure the line is level by using a level to draw the line.

Next, use the highest mark to draw a plumb line on the wall alongside the vanity, which will represent the width of one side of the vanity. Do the very same thing on the other side of the wall. Make certain these lines on the wall are plumb and level. What you should be left with is a level and plumb outline of your vanity.

Within this vanity outline there is at least one stud, possibly more. Find a stud and mark it so that you’ll know where to screw in the new vanity. Next, locate your pipes’ vertical and horizontal centerlines and indicate the location of each by marking plumb and level lines on the wall. Now, measure from the center of the drain line to where you have marked where the nearest vanity cabinet edge is to be placed, and do this down to the floor also. Finally, using the lines you made earlier as starting point measure to the center of each supply pipe.

With these measurements, you are now able to mark on the back of the new vanity where you will need to cut in order to allow for pipes and lines. After you have marked the location of the pipes and lines onto the back of the new vanity, drill holes at those marks. DON’T FORGET TO PUT ON YOUR SAFETY GOGGLES AND GLOVES FIRST.

Make certain that you cut pipe and line holes in the vanity back that are large enough to accommodate each pipe and line. Usually, cutting a space 0.5 inches or more will provide enough room for your water pipe and drain line. Note: drill only part of the way inside of the vanity from the outside of the vanity base, and then finish up your drilling from the inside of the vanity base to create a cleaner look.

Install the New Vanity

At last you are ready to secure the vanity to the wall. First, remove the vanity doors before installing to avoid damage. Then pre-drill holes into the back of your vanity that will match up with your wall studs. The holes should be ONE SIZE LARGER than your 2.5-inch screws, and the holes in the studs should be one to two sizes SMALLER to ensure your vanity will have a tight and secure fit.

Now, carefully slide the new vanity into place. Make certain your vanity is level in all positions (side to side, front to back). Remember, if is not level you can always use a wooden shim to level it, but the vanity must be level for proper installation. If you have to use a shim, take a chisel and hammer to cut off the edges of the shims that are sticking out—take care to not damage your bathroom floor.

Next, make certain that the new vanity is plumb and square. Once you are sure that it is, take your washers and 3-inch wood screws and drive them through the nailer (the piece of wood running across the back of the vanity) and into the wall studs in order to attach the vanity to the wall. Check once again that the vanity is level. Caulk around the sink and pipe areas.

And you have just finished installing a new bathroom vanity!

Know Common Problems when Installing Wallpaper

wallpaperWallpaper is a key factor in making your home a comfortable, welcoming space. However, installing wallpaper can be a very tedious task in the process of remodeling your home. It can be even more tedious with the problems that come with it. All of those problems can be prevented by following the proper guidelines. Here are some of the common problems and solutions in installing wallpaper in your home.

Holes and Tears

This can become a problem as wallpaper ages over the years. Holes and tears are a typical part of the wear and tear of the house.
You can easily fix this problem with leftover matching wallpaper. Just follow these simple steps and those tears will be nonexistent in no time:

– Carefully, using a sharp razor blade, strip off the torn area and the paper surrounding the area.
– With scissors, cut a corresponding portion from the leftover wallpaper.
– Cover the back of the new patch of wallpaper with a thin coat of wallpaper paste.
– Affix the new portion of wallpaper to the wall, using a damp cloth to even it out.

Seam Openings

Seam openings can be the effect of any of the following:

– Too much rolling of seams forcing wallpaper paste from behind wallcovering
– Not enough paste applied to edges when installing wallpaper
– Letting the paste dry on edges during installation

A simple solution to this problem would be to apply wallpaper paste or adhesive to the wall following these steps:

– Fill squeeze bottle with wallpaper paste or adhesive
– Apply the spout of the squeeze bottle under the edge of the wallpaper
– Apply a squirt of paste to any seam openings, adding a small amount of pressure
– Wipe away excess adhesive or paste with damp cloth

Curling and Loose Ends

These problems are another typical part of household wear and tear. They can be caused by simple slip-ups including the following:

– Installing wallpaper without proper preparation
– Not enough paste or adhesive applied
– Temperature caused adhesive to dry too quickly

This problem is common and can be easily taken care of by applying more wallpaper adhesive to the edges of the wallpaper.

Bubbles & Blisters

Another typical problem in installing wallpaper is the appearance of bubbles and blisters in the wallcovering. This may be an effect of:
– Not using enough paste during installation
– Not using a roller to smooth out the strip of wallpaper smoothly against the wall
– Not following the proper steps to prepare the surface of the wall before installation
– Not allowing strips to relax before continuing installation
– Applying wallpaper in places below 50 degrees F

The solution to eliminating bubbles and blisters is simple. Small bubbles can be puncture and flattened. On the other hand, large bubbles can be opened to add more adhesive and then patted flat.

See Through

In some cases, wallpaper is too thin and tends to be almost transparent, causing images on the wall to be seen. In this case, the solution would be to prepare the wall ahead of time. If the wallpaper may be seen through, applying a pigmented wallcovering primer to the wall will eliminate this problem. Lining paper should also be used in extreme cases.